Shipping to 
and 
Japan CLAS Corrections L6 Receiver NEO-D9C
Lorem Ipsum is simply dummy text of the printing and typesetting industry. Lorem Ipsum
has been the industry’s standard dummy text ever since the 1500s.
126,00€
Availability: In stock
This product comes with 2 years worldwide warranty
| Units | Price per unit |
|---|---|
| <50 | 126,00€ |
| >=50 | Contact us for special pricing |
| >500 | Contact us for special pricing |
Includes:
– Pre-configured NEO-D9C module with soldered headers (XBee socket compatible)
– Pigtail uFL to SMA-Male (20cm) so you can share one antenna with 2 receivers
Enhance your experience, add to your cart:
-
Shield for Septentrio Native Ethernet
Original price was: 42,00€.38,00€Current price is: 38,00€.
Japan CLAS Corrections L6 Receiver NEO-D9C
126,00€
Availability: In stock
This product comes with 2 years worldwide warranty
| Units | Price per unit |
|---|---|
| <50 | 126,00€ |
| >=50 | Contact us for special pricing |
| >500 | Contact us for special pricing |
Includes:
– Pre-configured NEO-D9C module with soldered headers (XBee socket compatible)
– Pigtail uFL to SMA-Male (20cm) so you can share one antenna with 2 receivers
QZSS is a constellation of satellites available over and around Japan. Via L6 band (L-band), these satellites provide 2 services:
- Centimeter Level Augmentation Service (CLAS) providing centimeter level correction data in Japan.
- Multi-GNSS Advanced Demonstration tool for Orbit and Clock Analysis (MADOCA) providing decimeter level correction in Japan and neighboring countries like South Korea.
If you are in this region, just:
- Plug ArduSimple CLAS Corrections L6 receiver onto your XBee socket
- Check that your ZED-F9P has firmware 1.32 or newer
- Configure ZED-F9P UART2 to accept UBX protocol in at 9’600bps
- Wait a few minutes and start enjoying high precision GNSS.
Good to know:
– Default configuration is for CLAS. Contact us for MADOCA settings.
– This board includes u-blox NEO-D9C
– The product includes an RF-splitter so you only need 1 antenna for both your RTK receiver and the L-band receiver. If you want you can also connect to separate antennas, one for the RTK receiver and another one for the L-band receiver.
– You will need a good L-band (L6) antenna to receive the correction stream like Calibrated Survey GNSS Tripleband + L-band antenna (IP67) or Lightweight helical GNSS Tripleband + L-band antenna (IP67)
– This XBee accessory is only compatible with u-blox ZED-F9P and ZED-F9R boards (simpleRTK2B series).
Specifications
Interfaces:- UART
- Voltage supply (VCC): 2.7 - 3.6V
- UART voltage: same as VCC
- Antenna supply: VCC - 0.3V
- Antenna input with SMA connector
- Antenna signal output for another receiver with uFL connector
Documentation
Start here:
Datasheet- We didn't find time to create this 3D CAD model, contact us to request it
You may also need…
-
RTK2B Boards
simpleRTK2B Budget
From 172,00€ This product has multiple variants. The options may be chosen on the product page -
-
-
-
-
Description
Survey grade and low cost Dual band (L1, L2/E5b/B2I) active
GNSS antenna with TNC connector and 2.5m cable terminated
with SMA male. Supports GPS, GLONASS, Galileo, and BeiDou.
Perfect match for u-blox ZED-F9P and Septentrio Mosaic-H
boards.
Good to know:
· Compatible with all simpleRTK2B boards as well as any other
multiband GNSS receiver in the market.
· Bulk pricing starting 50 units
Specifications
2B Survey Budget antenna
Antenna element
· Supported positioning signal bands:
· GPS: L1, L2
· GLONASS: G1, G2
· BeiDou: B1, B2
· Galileo: E1, E5b
· QZSS: L1, L2
· SBAS: WAAS, EGNOS, MSAS and GAGAN
· Polarization: RHCP
· Peak gain: 5dBi
· Axial Ratio @ zenith: <3dB
· Azimuth Coverage: 360 degrees
· Impedance: 50 ohm
· Phase center error: ±3mm
Electrical
· Supply voltage: 3-5.5V
· Typical supply current @ 3V: 50mA
· Average LNA gain: 40dB
· Maximum Noise Figure: 1.5dB
· Maximum VSWR: 2
Mechanical
· Maximum length: 147mm
· Weight: 390g
· Mounting style: Magnetic base (requires accessory) or 5/8” x
11TPI thread
· Connector: TNC female
· Cable length: Includes 2.5 meter cable terminated in SMA male
Environmental
· Operating Temperature: -40 to +85°C
· Storage Temperature: -40 to +85°C
· IP Rating: IP66 (excluding air vent in screw hole, which can be
sealed when installed
Documentation
Start here
QZSS is a constellation of satellites available over and around Japan. Via L6 band (L-band), these satellites provide 2 services:
- Centimeter Level Augmentation Service (CLAS) providing centimeter level correction data in Japan.
- Multi-GNSS Advanced Demonstration tool for Orbit and Clock Analysis (MADOCA) providing decimeter level correction in Japan and neighboring countries like South Korea.
If you are in this region, just:
- Plug ArduSimple CLAS Corrections L6 receiver onto your XBee socket
- Check that your ZED-F9P has firmware 1.32 or newer
- Configure ZED-F9P UART2 to accept UBX protocol in at 9’600bps
- Wait a few minutes and start enjoying high precision GNSS.
Good to know:
– Default configuration is for CLAS. Contact us for MADOCA settings.
– This board includes u-blox NEO-D9C
– The product includes an RF-splitter so you only need 1 antenna for both your RTK receiver and the L-band receiver. If you want you can also connect to separate antennas, one for the RTK receiver and another one for the L-band receiver.
– You will need a good L-band (L6) antenna to receive the correction stream like Calibrated Survey GNSS Tripleband + L-band antenna (IP67) or Lightweight helical GNSS Tripleband + L-band antenna (IP67)
– This XBee accessory is only compatible with u-blox ZED-F9P and ZED-F9R boards (simpleRTK2B series).
Specifications
Interfaces:- UART
- Voltage supply (VCC): 2.7 - 3.6V
- UART voltage: same as VCC
- Antenna supply: VCC - 0.3V
- Antenna input with SMA connector
- Antenna signal output for another receiver with uFL connector
Documentation
Start here:- Datasheet
- We didn't find time to create this 3D CAD model, contact us to request it
You may also need…
-
RTK2B Boards
simpleRTK2B Budget
From 172,00€ This product has multiple variants. The options may be chosen on the product page -
-
-
-
-
