Shipping to 
and 
NiMH Battery Shield
Lorem Ipsum is simply dummy text of the printing and typesetting industry. Lorem Ipsum
has been the industry’s standard dummy text ever since the 1500s.
68,00€
Availability: In stock
This product comes with 2 years worldwide warranty
| Units | Price per unit |
|---|---|
| <50 | 68,00€ |
| >=50 | Contact us for special pricing |
| >500 | Contact us for special pricing |
Includes:
– Battery Shield
– 3x mAh Battery Pack
– Arduino Headers Kit
Enhance your experience, add to your cart:
-
Shield for Septentrio Native Ethernet
Original price was: 42,00€.38,00€Current price is: 38,00€.
NiMH Battery Shield
68,00€
Availability: In stock
This product comes with 2 years worldwide warranty
| Units | Price per unit |
|---|---|
| <50 | 68,00€ |
| >=50 | Contact us for special pricing |
| >500 | Contact us for special pricing |
Includes:
– Battery Shield
– 3x mAh Battery Pack
– Arduino Headers Kit
Make your project autonomous with this rechargeable battery pack. This product includes a set of standard AAA rechargeable batteries that you will find in any shop. Simply plug in the batteries and recharge them via the USB-C connector.
- STAT LED (blue): ON when charging, OFF when fully charged or not charging, BLINKING when there is an error.
- LOW LED (red): ON when battery is low and about to switch off.
Good to know:
– Also compatible with Arduino Uno, Duemilanove, Mega, Leonardo and Due – basically any Arduino-pinout-shaped Arduino as only the GND and 5V pins are used.
– USB-C cable is not included, which is needed to charge the battery from your laptop or a wall adapter. If you don’t have you can get here our USB-C Cable.
– There’s currently a known misbehavior on the board, the STAT LED (blue) doesn’t turn OFF after charge is completed, unless you move the switch ON/OFF once after the battery is fully charged. We apologize for the inconvenience.
Specifications
Hardware features:- Voltage supply via USB: 4.5-5.5V
- Full charging time: 1 hour
- Battery: 3x Nickel Metal Hydride Battery AAA 1.2V 780 mAh
Documentation
Start here:
Datasheet- We didn't find time to create this 3D CAD model, contact us to request it
You may also need…
-
RTK starter kits
simpleRTK2B – Basic Starter Kitdgfhdh
From 237,00€ This product has multiple variants. The options may be chosen on the product page -
RTK starter kits
simpleRTK2B - 4G NTRIP Starter Kit
449,00€ This product has multiple variants. The options may be chosen on the product page -
Sale!
Made in EuropeRTK starter kitssimpleGNSS - Basic Starter Kit
Original price was: 99,00€.90,00€Current price is: 90,00€. -
-
Description
Survey grade and low cost Dual band (L1, L2/E5b/B2I) active
GNSS antenna with TNC connector and 2.5m cable terminated
with SMA male. Supports GPS, GLONASS, Galileo, and BeiDou.
Perfect match for u-blox ZED-F9P and Septentrio Mosaic-H
boards.
Good to know:
· Compatible with all simpleRTK2B boards as well as any other
multiband GNSS receiver in the market.
· Bulk pricing starting 50 units
Specifications
2B Survey Budget antenna
Antenna element
· Supported positioning signal bands:
· GPS: L1, L2
· GLONASS: G1, G2
· BeiDou: B1, B2
· Galileo: E1, E5b
· QZSS: L1, L2
· SBAS: WAAS, EGNOS, MSAS and GAGAN
· Polarization: RHCP
· Peak gain: 5dBi
· Axial Ratio @ zenith: <3dB
· Azimuth Coverage: 360 degrees
· Impedance: 50 ohm
· Phase center error: ±3mm
Electrical
· Supply voltage: 3-5.5V
· Typical supply current @ 3V: 50mA
· Average LNA gain: 40dB
· Maximum Noise Figure: 1.5dB
· Maximum VSWR: 2
Mechanical
· Maximum length: 147mm
· Weight: 390g
· Mounting style: Magnetic base (requires accessory) or 5/8” x
11TPI thread
· Connector: TNC female
· Cable length: Includes 2.5 meter cable terminated in SMA male
Environmental
· Operating Temperature: -40 to +85°C
· Storage Temperature: -40 to +85°C
· IP Rating: IP66 (excluding air vent in screw hole, which can be
sealed when installed
Documentation
Start here
Make your project autonomous with this rechargeable battery pack. This product includes a set of standard AAA rechargeable batteries that you will find in any shop. Simply plug in the batteries and recharge them via the USB-C connector.
- STAT LED (blue): ON when charging, OFF when fully charged or not charging, BLINKING when there is an error.
- LOW LED (red): ON when battery is low and about to switch off.
Good to know:
– Also compatible with Arduino Uno, Duemilanove, Mega, Leonardo and Due – basically any Arduino-pinout-shaped Arduino as only the GND and 5V pins are used.
– USB-C cable is not included, which is needed to charge the battery from your laptop or a wall adapter. If you don’t have you can get here our USB-C Cable.
– There’s currently a known misbehavior on the board, the STAT LED (blue) doesn’t turn OFF after charge is completed, unless you move the switch ON/OFF once after the battery is fully charged. We apologize for the inconvenience.
Specifications
Hardware features:- Voltage supply via USB: 4.5-5.5V
- Full charging time: 1 hour
- Battery: 3x Nickel Metal Hydride Battery AAA 1.2V 780 mAh
Documentation
Start here:- Datasheet
- We didn't find time to create this 3D CAD model, contact us to request it
You may also need…
-
RTK starter kits
simpleRTK2B – Basic Starter Kitdgfhdh
From 237,00€ This product has multiple variants. The options may be chosen on the product page -
RTK starter kits
simpleRTK2B - 4G NTRIP Starter Kit
449,00€ This product has multiple variants. The options may be chosen on the product page -
Sale!Made in EuropeRTK starter kits
simpleGNSS - Basic Starter Kit
Original price was: 99,00€.90,00€Current price is: 90,00€. -
-
