Shipping to 
and 
Shield for Septentrio Native Ethernet
Lorem Ipsum is simply dummy text of the printing and typesetting industry. Lorem Ipsum
has been the industry’s standard dummy text ever since the 1500s.
Original price was: 42,00€.38,00€Current price is: 38,00€.
Availability: In stock
This product comes with 2 years worldwide warranty
| Units | Price per unit |
|---|---|
| <50 | 38,00€ |
| >=50 | Contact us for special pricing |
| >500 | Contact us for special pricing |
Includes:
– 1x Shield for Septentrio Native Ethernet
– 1x Arduino Headers Kit
Enhance your experience, add to your cart:
-
Shield for Septentrio Native Ethernet
Original price was: 42,00€.38,00€Current price is: 38,00€.
Shield for Septentrio Native Ethernet
Original price was: 42,00€.38,00€Current price is: 38,00€.
Availability: In stock
This product comes with 2 years worldwide warranty
| Units | Price per unit |
|---|---|
| <50 | 38,00€ |
| >=50 | Contact us for special pricing |
| >500 | Contact us for special pricing |
Includes:
– 1x Shield for Septentrio Native Ethernet
– 1x Arduino Headers Kit
With the ArduSimple Shield for Native Ethernet you can expand your simpleRTK3B Pro or Heading Board to use the integrated Ethernet functionality inside Septentrio Mosaic.
With this accessory you will be able to configure the Ethernet features directly from the Septentrio web interface.
Good to know:
– Note that this accessory only works with Septentrio boards shipped after January 2023. Contact us if you have any doubt.
– This accessory requires that your Septentrio module is updated with firmware v4.14.0 or newer.
– This product includes a set of Headers in case your ArduSimple board is without headers soldered.
How to use it:
1. Stack it on top of your simpleRTK3B with headers soldered.
2. Move the switch on your simpleRTK3B towards 5V = OUT.
3. Connect via USB and go to the Septentrio Web Interface, section Ethernet and turn the feature ON.
4. Default configuration is expecting a DHCP server in your network, otherwise you can set manually your preferred IP settings.
5. Store these new settings in memory, so they remain after a power cycle.
Specifications
Hardware features:- Voltage supply: 4.5V - 5.5V
- Connector: RJ45
Documentation
Start here:Certifications:
You may also need…
-
RTK3B Boards
simpleRTK3B Pro
From 569,00€ This product has multiple variants. The options may be chosen on the product page -
RTK3B Boards
simpleRTK3B Heading
From 699,00€ This product has multiple variants. The options may be chosen on the product page -
-
AccessoriesPlastic Case for simpleRTK boards
From 39,00€ This product has multiple variants. The options may be chosen on the product page -
Description
Survey grade and low cost Dual band (L1, L2/E5b/B2I) active
GNSS antenna with TNC connector and 2.5m cable terminated
with SMA male. Supports GPS, GLONASS, Galileo, and BeiDou.
Perfect match for u-blox ZED-F9P and Septentrio Mosaic-H
boards.
Good to know:
· Compatible with all simpleRTK2B boards as well as any other
multiband GNSS receiver in the market.
· Bulk pricing starting 50 units
Specifications
2B Survey Budget antenna
Antenna element
· Supported positioning signal bands:
· GPS: L1, L2
· GLONASS: G1, G2
· BeiDou: B1, B2
· Galileo: E1, E5b
· QZSS: L1, L2
· SBAS: WAAS, EGNOS, MSAS and GAGAN
· Polarization: RHCP
· Peak gain: 5dBi
· Axial Ratio @ zenith: <3dB
· Azimuth Coverage: 360 degrees
· Impedance: 50 ohm
· Phase center error: ±3mm
Electrical
· Supply voltage: 3-5.5V
· Typical supply current @ 3V: 50mA
· Average LNA gain: 40dB
· Maximum Noise Figure: 1.5dB
· Maximum VSWR: 2
Mechanical
· Maximum length: 147mm
· Weight: 390g
· Mounting style: Magnetic base (requires accessory) or 5/8” x
11TPI thread
· Connector: TNC female
· Cable length: Includes 2.5 meter cable terminated in SMA male
Environmental
· Operating Temperature: -40 to +85°C
· Storage Temperature: -40 to +85°C
· IP Rating: IP66 (excluding air vent in screw hole, which can be
sealed when installed
Documentation
Start here
With the ArduSimple Shield for Native Ethernet you can expand your simpleRTK3B Pro or Heading Board to use the integrated Ethernet functionality inside Septentrio Mosaic.
With this accessory you will be able to configure the Ethernet features directly from the Septentrio web interface.
Good to know:
– Note that this accessory only works with Septentrio boards shipped after January 2023. Contact us if you have any doubt.
– This accessory requires that your Septentrio module is updated with firmware v4.14.0 or newer.
– This product includes a set of Headers in case your ArduSimple board is without headers soldered.
How to use it:
1. Stack it on top of your simpleRTK3B with headers soldered.
2. Move the switch on your simpleRTK3B towards 5V = OUT.
3. Connect via USB and go to the Septentrio Web Interface, section Ethernet and turn the feature ON.
4. Default configuration is expecting a DHCP server in your network, otherwise you can set manually your preferred IP settings.
5. Store these new settings in memory, so they remain after a power cycle.
Specifications
Hardware features:- Voltage supply: 4.5V - 5.5V
- Connector: RJ45
Documentation
Start here:Certifications:You may also need…
-
RTK3B Boards
simpleRTK3B Pro
From 569,00€ This product has multiple variants. The options may be chosen on the product page -
RTK3B Boards
simpleRTK3B Heading
From 699,00€ This product has multiple variants. The options may be chosen on the product page -
-
Accessories
Plastic Case for simpleRTK boards
From 39,00€ This product has multiple variants. The options may be chosen on the product page -
